HomeDoulton RIO-2000, Pentek Filters, Pentair Everpure Descalers

Whole House Slimline Salt Free Water Softener, Taste, Odour, Chlorine, Pentek Cartridge
Whole House Slimline Salt Free Water Softener, Taste, Odour, Chlorine, Pentek Cartridge
Whole House Slimline Salt Free Water Softener, Taste, Odour, Chlorine, Pentek Cartridge
Whole House Slimline Salt Free Water Softener, Taste, Odour, Chlorine, Pentek Cartridge
Whole House Slimline Salt Free Water Softener, Taste, Odour, Chlorine, Pentek Cartridge

Whole House Slimline Salt Free Water Softener, Taste, Odour, Chlorine, Pentek Cartridge

Product code: tsgac-10
£67.14
You will earn 67 points with this purchase

WHOLE HOUSE SLIMLINE SALT FREE WATER SOFTENER, TASTE, ODOUR, CHLORINE, PENTEK CARTRIDGE

This is a 2 stage water filter & water softening cartridge based system, Slimline but High Flowrate at 1 Bar & above, in normal use we'd expect the cartridge to last 3 - 6 months to 1 year maximum, before replacements are needed. See figures below.

The First Stage Filter contains granular activated carbon to effectively reduce unwanted taste and odor, and chlorine taste & odor, as well as The Second stage contains phosphate crystals to reduce rust stains and calcium scale deposits, this effectively softens the water.

it comes complete with:

  • One (1) housing brackets
  • One (1) Slimline Housing (blue)
  • One (1) Housing Spanner
  • 1 (one) Pentek Water TSGAC-10 ANTI-SCALE, Chlorine, Taste & Odour Cartridges
With Flow rates from:
    • 2.5psi @ 1.0gpm (0.17bar @ 3.8Lpm)

The manufacturer states that the Water Filtering capacity is:
Pentek Water TSGAC-10 : 2000 Gallons at 1 Gpm or 7570L at 3.8Lpm

The Filter Cartridge Specs:

PENTEK WATER TSGAC Anti-Scale, Chlorine, Taste & Odour cartridge:

TSGAC cartridges contain granular activated carbon to effectively reduce unwanted tastes and odors, including chlorine taste & odor, as well as phosphate crystals to reduce rust stains and scale deposits.

The construction of the cartridge allows water to enter at one end and pass through the entire length of the carbon bed before exiting the other end of the cartridge. An internal expansion pad minimizes channeling or bypass. This design allows for maximum contact between the water and carbon, ensuring maximum adsorption.

Before the water exits the cartridge, a post-filter helps remove carbon fines and other suspended particles from the filtered water. The post-filter is permanently fastened to an innovative support basket ensuring that it is firmly secured and eliminating any potential for bypass.

Pentek TSGAC Cartridges provide superior performance and outstanding protection for your water lines, fixtures, major appliances and commercial equipment.

HOW TO ASSEMBLE THIS FILTER UNIT.
IF YOU HAVE ANY DOUBTS CONCERNING INSTALLATION WE ALWAYS RECOMMEND THAT YOU USE A COMPETENT / REGISTERED PLUMBER

1. ENSURE THAT THE UNIT IS "FACING FRONT" & IN CORRECT ALIGNMENT FOR WATER FLOW. CONSIDER THE SPACING REQUIRED AROUND THE UNIT TO ALLOW ADEQUATE PIPE WORK CONNECTIONS. TIP: USE PTFE TAPE ON ALL CONNECTIONS TO ENSURE A GOOD WATERTIGHT SEALS.
ADVICE TIP: LAY TOP ON A LONG ENOUGH & STRONG ENOUGH PIECE OF FLAT PLYWOOD TO ENABLE LIFTING INTO POSITION & MARKING OF BRACKET DRILL HOLES.

2. CONNECT THE BRACKET TO THE HOUSING TOP. ENSURING THAT YOU USE THE "HOUSING-BRACKET BOLTS" TO CONNECT THE BRACKET TO THE HOUSINGS. NEXT ATTACH THE EMPTY HOUSING TO THE HOUSING COVER.
ADVICE TIP: STAND UNIT ON A LONG ENOUGH & STRONG ENOUGH PIECE OF FLAT PLYWOOD TO ENABLE LIFTING INTO POSITION & MARKING OF BRACKET DRILL HOLES
TIP: YOU CAN HAVE THE BRACKET ALIGNED WITH THE SHORT ARM OF THE "L" FACING UP OR DOWN, IN ACCORDANCE WITH YOUR AVAILABLE SPACE, BUT, IT IS EASIER TO MARK & FIT IF, THE SHORT ARM OF THE "L" FACES UP.  IF INSTALLING WITH THE SHORT ARM OF THE 'L" DOWN, YOU CAN ATTACH THE BRACKET TO THE HOUSING TOP, AFTER THE BRACKETS HAVE BEEN INSTALLED. THE HOUSINGS DO NOT HAVE TO BE DONE UP TIGHTLY, TILL LATER.

3. SELECT THE INSTALLATION POINT FOR THE FILTER UNIT, ENSURE SELECTED LOCATION IS ROBUST ENOUGH TO CARRY THE WEIGHT OF THE COMPLETE ASSEMBLY. (TOTAL WEIGHT WILL BE IN EXCESS OF: 4KGS, ALBEIT SPREAD OVER 4 FIXING POINTS)  MARK THE INSTALLATION POINT OF THE WALL BRACKETS & PREPARE LOCATION TO BE ATTACHED ACCORDINGLY (IE: PRE-DRILL HOLES, INSERT WALL PLUGS, ETC. AS NEEDED) TIP: LEAVE ENOUGH ROOM BELOW THE BOTTOM OF THE HOUSING TO ALLOW REMOVAL FOR MAINTENANCE, CARTRIDGE REPLACEMENT ETC, IT MAY ALSO BE DESIRABLE TO LEAVE ENOUGH ROOM BELOW FOR A DRIP TRAY TOO. YOU WILL NEED A SECOND / THIRD PAIR OF HANDS FOR THIS PART.

4. INSTALL BRACKET TO PREVIOUSLY MARKED POSITIONS, ENSURE YOU USE THE CORRECT TYPE OF WALL BOLTS, SCREWS, ETC ACCORDING TO THE WALL SURFACE.TIGHTEN SCREWS THAT SECURE THE HOUSING TO THE WALL BRACKET.

5. INSERT FILTER INTO HOUSING, TIGHTEN UP HOUSINGS USING THE SUPPLIED SPANNER. ENSURE YOU HAVE THE HOUSING CORRECTLY POSITIONED FOR THE DIRECTION OF INCOMING WATER FLOW.

6. SLOWLY TURN ON WATER SUPPLY & ALLOW HOUSINGSTO FILL COMPLETELY, YOU MIGHT HAVE TO OPERATE THE RED PRESSURE RELEASE VALVE. CHECK FOR LEAKS. (FIX ACCORDINGLY) NEXT TURN ON THE FIRST WATER OUTLET AFTER THE INSTALLATION, TAP, ETC, TO ALLOW TRAPPED AIR TO BE EXPELLED. RUN THE WATER OUTLET FOR THE RECOMMENDED TIME FOR THE FILTER UNIT AS PER THE INSTRUCTIONS FOUND INSIDE FILTER BOX / PACKAGING.

7. CARRY OUT REGULAR CHECKS & MAINTENANCE OF THE FILTRATION UNIT AS WOULD BE REQUIRED ACCORDING TO YOUR WATER USE.
Write a review and share your thoughts with other shoppers.
Product Code tsgac-10
Brand Pentek
Condition New